JVC RX-6022VSL
Manual de Usuario

Using DAP Modes and All Channel Stereo
Once you have adjusted the DAP modes and All Channel Stereo, the adjustment is memorized for each source. � You cannot use the DAP modes and All Channel Stereo if no rear speakers are connected and activated. � You cannot adjust the effect level for All Channel Stereo.

When Surround mode turns on, the last selected Surround mode will be activated. � Each time you press the button, Surround mode turns on and off alternately.

3

From the remote control:
It will be convenient for you to use the remote control for adjustments, since you can make adjustments from your listening point.

Press SURROUND MODE SURROUND MODE repeatedly until one of the DAP modes��LIVE CLUB,� �DANCE CLUB,� �HALL,� �PAVILION,�� or �ALL CH STEREO� appears on the display.
The DSP indicator also lights up on the display.

If you like to adjust sound, go to step 4.

1 2

Start playing 2 channel software�either analog or Linear PCM�and select the source. Press SURROUND ON/OFF to activate Surround mode.
ON/OFF

4

SURROUND

When Surround mode turns on, the last selected Surround mode will be activated. � Each time you press the button, Surround mode turns on and off alternately.

Adjust the speaker output levels. 1) Press ADJUST repeatedly until one of the following indications (with the current setting)* appears on the display.

ADJUST

REAR L : To adjust the left rear speaker output level (�10 to +10). REAR R : To adjust the right rear speaker output level (�10 to +10). CENTER : For �ALL CH STEREO� only�to adjust the center speaker output level (�10 to +10). * �0� is the initial setting. If you have already changed the setting, another number (level) will be shown.

3

Press SURROUND MODE repeatedly until one of the DAP modes��LIVE CLUB,� �DANCE CLUB,� �HALL,� �PAVILION��or �ALL CH STEREO� appears on the display.
The DSP indicator also lights up on the display.

SURROUND
MODE

If you like to adjust sound, go to step 4.

4 5

Press SOUND.
10 keys are activated for sound adjustments.

SOUND

2) Press CONTROL UP 5/DOWN � to adjust the selected speaker output levels. 3) Repeat steps 1) and 2) to adjust the
other speaker levels.

CONTROL DOWN UP

Adjust the speakers output levels (�10 to +10).
� To adjust the left rear speaker level, press REAR�L +/�. � To adjust the right rear speaker level, press REAR�R +/�. For �ALL CH STEREO� only: � To adjust the center speaker level, press CENTER +/�.
2
5

REAR L

6

REAR R

5

8

9

Only for DAP modes: Adjust the DSP effect level.

CENTER

3

1) Press ADJUST repeatedly until �EFFECT� (with the current setting)* appears on the display.

ADJUST

Creating Realistic Sound Fields

6

For DAP modes only: Press EFFECT to select the effect level (1 to 5) you want.

EFFECT

* �EFFECT 3� is the initial setting. If you have already changed the setting, another setting will be shown.

4

2) Press CONTROL UP 5/DOWN �
to select the effect level (1 to 5) you want.
� Each time you press the button, the effect level changes as follows:

DOWN

CONTROL

UP

� Each time you press the button, the effect level changes as follows: EFFECT 1 EFFECT 2 EFFECT 3 EFFECT 5 EFFECT 4

EFFECT 1 EFFECT 5

EFFECT 2

EFFECT 3 EFFECT 4

As the number increases, the selected mode becomes stronger (normally set it to �EFFECT 3�).

On the front panel:

As the number increases, the selected mode becomes stronger (normally set it to �EFFECT 3�).
Note: You cannot select any DAP mode and All Channel Stereo for Dolby Digital and DTS Digital Surround.

1 2

Start playing 2 channel software�either analog or Linear PCM�and select the source. Press SURROUND ON/OFF to activate Surround mode.
SURROUND ON/OFF

To cancel DAP modes and All Channel Stereo
Press SURROUND ON/OFF so that �SURROUND OFF� appears on the display. The DSP indicator goes off.

23