No hay comentarios de productos.
Multi-Brand Control Feature
Multi-Brand Control Setup
The Remote Control can be set to control some TV and Cable box/DSS functions.
Advanced Connections
Audio/Video connection If your TV has AUDIO IN and VIDEO IN terminals, you can connect your VCR to them to receive higher quality picture and sound.
MTS Broadcast/VHS Hi-Fi Stereo System
Connection Make the Audio/Video Connection as shown on page 3.
� You can use a TV connected to Stereo amp and speakers instead of a Stereo TV.
TV
VCR
® -TV Noise Equipped with Reduction for true MTS reproduction. ® -TV Noise Reduction is required for good stereo separation and audio fidelity. ® is a registered trademark, and is licensed by ®
Timer Recording Using VCR Plus+ System
VCR Plus+ System is ...
This feature sets most items of a Timer Recording when you enter a PlusCode programming number found in TV GUIDE and selected newspaper TV listings. Initial Setup..... To use VCR Plus+ system, clock and channels must be set (p. 4 of �Basic Operations� book). Channel Setup..... Broadcast/ cable stations are assigned a VCR Plus+ (GUIDE CH) number. See the Channel Listing (directory) page of TV GUIDE, etc. In the Channel Setup below, you will be entering your local channel number (RECEIVE CH) for each GUIDE CH number. Example : if NBC�s assigned GUIDE CH were 05, and your TV received NBC on channel 04, you would enter 04 across from GUIDE CH 05 in step 3 of �VCR Plus+ System Channel Setup�.
Tape Operation
marks start and end points of commercials within recordings over 15 minutes long. The VCR automatically advances through marked commercials at high speed. Or, you may set to manual. Because stations broadcast differently, the effectiveness of this feature may vary. See bottom of page for answers to commonly asked questions about this feature.
Tape Operation
Playback
marked recordings can be played back so that commercial blocks are advanced through automatically or manually.
MTS Broadcast VHS Hi-Fi Stereo Timer Recording Using VCR Plus+ System � Tape Operation
� Tape Operation
Playback
helps you locate certain parts of prerecorded movies (rented or purchased). The feature works in two ways. � You can go to the beginning of the movie. � You can skip from one preview to the next. works only on tapes recorded in SP speed with the record tab removed.
To Search for Preview.
You can override the operation of SEARCH FOR PREVIEWS mode by pressing SEARCH/ M/A SKIP during tape searching. works by searching the tape past each preview and then reversing back to the start of the detected preview. While the tape is reversing back, if SEARCH/ M/A SKIP is pressed, will begin searching for the next preview. While searching for the next preview, if you see the start of a preview which you wish to watch, press SEARCH/ M/A SKIP and will immediately reverse back to the start of that preview, instead of searching further past the preview start point. Once the VCR is playing a preview, press SEARCH/ M/A SKIP to advance to the next preview, long commercial or the start of the movie (whichever is next).
1 Find your TV and Cable Box/DSS Receiver Brand Code Number from those shown below. 2 Setup for TV control,
� hold down TV button, � enter code with NUMBER keys.
1
Setup for Cable or DSS control,
� hold down DSS/CABLE button, � enter code with number keys. � If code number is 100 or greater, � press 100 key, then other digits. E.g., press 100 - 0 - 2 for 102.
VCR
IN FROM ANT. TV
R L
VCR C/A REPEAT PLAY CLOCK :OFFCH REMOTE WARNING :ON AUTO SHUT- OFF :OFF IDIOMA/LANGUE : ENGLISH VCR� S OUTPUT CH :3
SELECT : EXIT : ACT I ON
Press ACTION to display MENU.
Stereo Amplifier AUDIO OUT
R R L
Marking
With C/A RECORD: ON, the VCR auto rewinds after a recording is made and marks start and end points of all detected commercial blocks. After marking, the tape is returned to end of recording. Commercials are not erased.
1 Insert a tape without record tab. 2 Press SEARCH/ M/A
INDEX SEARCH PROG. END MOVIE
2
AUDIO OUT
R L
VHF/UHF
R
OUT TO TV
AUDIO IN
L
VCR Plus+ System Channel Setup
For [VCR-TV] or [VCR-cable box-TV] connection only. You�ll need a local TV channel listing (e.g. TV GUIDE) which includes the assigned VCR Plus+ numbers. VCR C / A CLOCK CHANNEL Press ACTION ANTENNA : CABLE AUTO SET to display menu, and WEAK SIGNAL DISPLAY : OFF CABLE/DSS BOX SET UP Press VCR Plus+ CH SET UP to select CHANNEL.
VCR Plus+ System Programming
AUDIO IN
OUT TO TV R L VHF/UHF
VCR C/A CLOCK CH SET UP COMMERCIAL ADV. C/A RECORD :ON C/A PLAYBACK :AUTO
3 Confirm code entry,
� press POWER to turn your TV on or off. � See table below for controllable functions in each mode. Notes � Repeat setup after remote battery replacement. � Remote will not control every TV, cable box, or DSS made by the manufacturer listed. If you get no response, your particular unit cannot be controlled. There are NO additional codes for the products listed. If your product is not listed, then the remote is not compatible with that product.
Technology Licensing.
1 Press PROG/VCR+ button to display PROGRAM. 2 Press to select display VCR Plus+
VCR Plus+ PROG. LIST ENTER PLUSCODE NUMBER USING 0 - 9 KEYS
Press to select C/A and display SET UP COMMERCIAL ADV.
ENTER INDEX NUMBER :1 USING 1- 9 KEYS FORWARD SEARCH :FF REVERSE SEARCH :REW NEXT :SEARCH M/A SK I P EXIT :STOP
SKIP to display SEARCH.
VIDEO OUT
screen.
1
Receivable Broadcast Types
VIDEO IN
1
REPEAT PLAY :OFF REMOTE WARNING :ON AUTO SHUT- OFF :OFF IDIOMA/LANGUE : ENGLISH VCR� S OUTPUT CH :3 SELECT : EXIT : ACT I ON
VCR
C/A
CLOCK
CH
Press ACTION*
SELECT : EXIT : ACT I ON
to display MENU.
3
VCR C/A CLOCK CH SET UP COMMERCIAL ADV. C/A RECORD :ON C/A PLAYBACK :AUTO
The following are possible audio broadcast types and on-screen displays. The signal being received is indicated with an � � mark while the selected audio mode is indicated with an arrow. To display the broadcast signal being received, � press DISPLAY*. MTS Stereo and SAP broadcast
STOP
STEREO SAP MONO
3
SELECT : EXIT : ACT I ON
Using Multi-Brand Control
After remote is set up, you can select VCR, TV, or DSS/CABLE for the desired function. Press VCR, or TV, or DSS/CABLE on the remote. (Table below shows available unit buttons for each mode.) Unit VCR TV CABLE/ DSS Mode VCR All VOL UP/DOWN
1 2 : 0 0AM CH 02 0 : 00 : 00 SP
2
1 2
Connect the VCR�s VIDEO OUT jack to the TV�s VIDEO IN jack.
Multi-channel Television Sound Stereo (main language) and Secondary Audio Program (sub language) broadcasts are being received simultaneously. Select STEREO or SAP audio mode.
VCR C / A CLOCK CHANNEL ANTENNA : CABLE AUTO SET WEAK SIGNAL DISPLAY : OFF CABLE/DSS BOX SET UP VCR Plus+ CH SET UP
SELECT : SET : EXIT : ACT I ON
Press
to select VCR Plus+ CH SET UP, and press to set.
Press NUMBER keys to enter PlusCode number and press 1 PROG/VCR+ button � If the PlusCode to set. number entered To Make Corrections, begins with �0,� skip press repeatedly to step 5. Display in to delete number, then step 4 will not appear. repeat step 3.
ENTER PLUSCODE NUMBER
VCR Plus+
PROG.
LIST
Press to select C/A PLAYBACK and press to set �AUTO� or �MANUAL�.
2
VCR
C/A
CLOCK
CH
SET UP COMMERCIAL ADV. C/A RECORD :ON C/A PLAYBACK :AUTO
Press to select C/A and display SET UP COMMERCIAL ADV.
SELECT : SET : EXIT : ACT I ON
Press SEARCH/ M/A SKIP twice to select GO TO START MOVIE MOVIE and press GO TO PREVIEW SEARCH START : FF to select GO TO SELECT : START MOVIE or GO EXIT : SEARCH M/A SK I P TO PREVIEW. Select �GO TO START MOVIE,� if you want to advance directly to beginning of the movie.
3
INDEX
SEARCH PROG. END
MOVIE
1 Start preview searching.
1) In step 3 at left, select Go To PREVIEW. 2) Press FF. � If you want to playback, press PLAY.
AUTO : VCR will automatically advance through marked commercial blocks recorded on the tape and then resume playback. MANUAL : VCR will advance through commercials only when CA/ZERO is pressed. Playback will resume when the end mark of a commercial block is found, or a new recording or blank portion is detected, or after 8 minutes.
� continue with step 4. Select �GO TO PREVIEW,� if you want to view the first (next) preview. � go to �To Search for Preview� at right. Press FF to start SEARCH INDEX PROG. END MOVIE searching.
SELECT : EXIT : ACT I ON
3
4
Press to move cursor to right, press to enter number, press to set, press to scroll up/down.
3
Connect VCR�s L/R AUDIO OUT jacks to the TV�s L/R AUDIO IN jacks.
MTS Stereo broadcast
Multi-channel Television Sound Stereo broadcast. Select STEREO audio mode.
STOP STEREO SAP MONO 1 2 : 0 0AM CH 02 0 : 00 : 00 SP
VCR C / A CLOCK
GUIDE CH 01 02 03
CHANNEL
TV CABLE/ DSS
Notes
VCR/TV, PLAY, STOP, EJECT, SAP/ Hi-Fi, DISPLAY, FF, REW, PAUSE/SLOW, REC, SPEED, CA/ZERO, COUNTER RESET, TAPE POSITION
POWER, INPUT, number keys, ENTER, CH UP/ DOWN, VOL UP/DOWN VOL UP/DOWN POWER, ENTER, NUMBER keys (except 100key), CH UP/ DOWN
RECEIVE CH ----
3
Set the VIDEO/TV selector of your TV (Monitor/Receiver) to �VIDEO.�
� If stereo broadcast is weak and display flickers, select MONO audio mode for possibly better results.
� Not all functions listed may be controllable. � In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing NUMBER keys for channel selection.
SAP broadcast
Secondary Audio Program (sub language) broadcast. Select SAP audio mode for the sub language.
STOP STEREO SAP MONO
1 2 : 0 0AM
CH 02 0 : 00 : 00 SP
TV Brand Code Numbers
Panasonic ....................... 01, 02 Quasar ............................ 01, 02 RCA ...................................... 03 GE ......................................... 03 Zenith .................................... 04 Magnavox ............................. 05 Sylvania ................................ 05 Sharp .............................. 06, 07 Sony ...................................... 08 Toshiba ................................. 09 Sanyo .................................... 10 Fisher .................................... 10 JVC ....................................... 11 Hitachi ................................... 12 Mitsubishi ........................ 07, 13 Samsung ............................... 14 Gold Star ................... 15, 16, 17
� Repeat step 3 until list is complete. � Leave line blank if station is not received CLEAR : ADD/DLT SET: : or if GUIDE and SELECT EXIT : ACT I ON RECEIVE CHs are the same. To Make Corrections, press and to move to error, then to change, or ADD/DLT to erase number.
GUIDE CH 01 02 03
VCR C / A CLOCK
5
RECEIVE CH ----
CHANNEL
Press to select ONCE, DAILY ONCE DAILY(MON-FRI) (MON~FRI), or WEEKLY WEEKLY record frequency and press PROG/VCR+ SELECT : END : PROG button to set. VCR Plus+ PROG. LIST Press to change DATE START STOP CH record speed and 13 SAT 2:20P 3:20P 02 press to set. TODAY
SELECT RECORD SPEED SELECT : SET: END : PROG SLP
VCR Plus+
PROG.
LIST
VCR C/A CLOCK CH SET UP COMMERCIAL ADV. C/A RECORD :ON C/A PLAYBACK :AUTO
Press to select C/A RECORD and press to set �ON� or �OFF�.
4
SEARCHING FOR START OF MOVIE
When a preview is detected, VCR will start playback.
� To cancel, press STOP.
2 Start next preview searching.
Press SEARCH/ M/A SKIP. � To cancel, press STOP.
SELECT : SET : EXIT : ACT I ON
CANCEL : STOP
ON: Timer recording, VCR Plus+ System, and One Touch recordings are marked automatically.
THE VCR IS WAITING TO MARK COMMERCIALS IN THE PROGRAM YOU RECORDED.
4 Press ACTION again to return to normal screen.
Notes � The mode set in step 3 remains unless a power outage occurs in which case the factory setting will be restored. � If playback is started in the middle of a commercial, only a single commercial is shown, or a single commercial is longer than 1 minute, a commercial may not be skipped. Press FF to quickly advance through the commercial. � Part of a recorded program may be skipped over if the program portion between commercials is less than one minute or there are frequent dark and quiet scenes in the program. To correct, press PLAY during the skip, rewind tape to just prior to where skipping started, then press PLAY again for normal playback. When the end of the commercials is detected, auto advance will resume.
are answered below.
When the movie is found...
5
INDEX
SEARCH PROG. END
MOVIE
Press PROG/VCR+ button to end program. Press PROG/VCR+ button again to exit. � Press ADD/DLT to delete the program.
6
VCR Plus+ PROG. DT START STOP 13 2 : 00 P 3 : 20P -- -- : -- -- : --- -- : -- -- : --- -- : -- -- : --
LIST CH SPD 02 SLP -- --- --- --
MARKING NOW : PRESS 1 LATER : PRESS 2 CANCEL : PRESS ACTION
� When timer is used to record two consecutive shows (same channel), greater accuracy can be obtained by programming each show separately.
Press PLAY to start playback. � To cancel, press STOP.
THE MOV I E I S READY START : PLAY CANCEL : STOP
Search System
For each recording, an invisible index mark is placed on the tape. A program index and information are also included for timer recordings. These marks are used to access or scan recordings.
I With a Cable Box (VCR
ANT or CATV AUDIO
IN FROM ANT.
Cable Box)
TV
You Can
� view any (including scrambled) channel. � use VCR Remote Control to select channels without using Multi-brand control feature.
You Cannot
� record scrambled channels.
4 Press ACTION twice to end setup.
MONO broadcast
Normal monaural sound broadcast.
STOP STEREO SAP MONO 1 2 : 0 0AM CH 02 0 : 00 : 00 SP
off to set timer recording. 7 Press POWER on Multi Function Display.) (�TIMER� lights Notes � Do not overlap program times. � See �Important for DSS/Cable Box Users� left. � Make each entry within 1 minute or VCR exits setup. � Once VCR Plus+ channel setup is done, channels stay in memory. If there�s a power outage, channel setup may be lost. Please do channel setup again. � Obtain unlisted PlusCode numbers by calling 1 - 900 - 454 - 7587. Call costs about $.95 per minute.
CANCEL : ADD / DLT SELECT : SET : EXIT : PROG
R L VHF/UHF
Cable Box Brand Code Numbers
Archer ............................... 05, 06, 01, 44, 63, 91, 126 Cabletenna ................................... 01, 44, 63, 91, 126 Cableview ................. 63, 44, 42, 30, 52, 04, 124, 126 Century ......................................... 51, 44, 59, 75, 126 Citizen ...................... 63, 44, 42, 30, 52, 04, 124, 126 Curtis .............................................. 08, 09, 61, 53, 87 Diamond ....................................... 01, 44, 63, 91, 126 Drake ..................................................................... 67 Eagle .......................... 13, 22, 58, 62, 20, 40, 26, 107 Eastern .......................................................... 28, 130 GC Brand ................. 63, 44, 42, 30, 52, 04, 124, 126 Gemini ........................................................... 04, 124 General Electric ............................................... 57, 01 General Instruments .. 01, 02, 03, 04, 34, 55, 83, 106, 65, 67, 68, 115, 117, 118, 124, 91 Hamlin .......... 14, 15, 28, 41, 102, 103, 104, 108, 130 Hitachi ................................................................... 31 Jasco ............................................................. 04, 124 Jerrold ....................... 01, 02, 03, 04, 34, 55, 83, 106, 65, 67, 68, 115, 117, 118, 124, 91 Macom .................................................................. 31 Magnavox ...................................................... 26, 112 Matsushita .......................................... 16, 17, 97, 109 Movietime ......................... 32, 39, 42, 44, 126, 38, 40 NEC .......................................................... 38, 40, 32 NOVAVISION ................................. 08, 09, 61, 53, 87 NSC .......................................................... 38, 40, 32 Oak ........................................................... 46, 11, 129 Oak Sigma ............................................... 46, 11, 129 Panasonic .......................................... 16, 17, 97, 109 Philips ....................... 07, 13, 20, 23, 24, 50, 128, 129 Pioneer ............................................................ 05, 06 Pulsar ....................... 63, 44, 42, 30, 52, 04, 124, 126 Quest ............................................................... 05, 06 Radio Shack ................................. 51, 44, 59, 75, 126 RCA ................................................... 16, 17, 97, 109 Realistic ........................................ 51, 44, 59, 75, 126 Recoton ........................................ 51, 44, 59, 75, 126 Regal ............ 14, 15, 28, 41, 102, 103, 104, 108, 130 Regency ........................................................ 28, 130 Rembrandt ........................ 01, 32, 39, 42, 44, 63, 126 Salora .................................................................... 68 Samsung ........................................ 05, 32, 40, 42, 06 Scientific Atlanta ............................. 08, 09, 61, 53, 87 Sheritech ............................................................... 27 Signal ............................................................ 26, 112 SL Marx ................ 32, 40, 42, 06, 43, 44, 52, 63, 126 Sprucer ............................................... 16, 17, 97, 109 Standard Components .................. 32, 39, 42, 44, 126 Stargate .. 32, 40, 63, 44, 42, 30, 52, 04, 06, 124, 126 Sylvania ................................................................. 19 Teknika .................................................................. 74 Telecaption .................................................... 77, 127 Teleview ............................................... 32, 40, 42, 06 Texscan ........................................................... 66, 19 Tocom ...................................... 33, 34, 01, 42, 18, 91 Toshiba ................................................................. 36 Uniden Satelite ...................................................... 65 Unika ............................................ 01, 44, 63, 91, 126 Universal ................................ 42, 43, 44, 52, 63, 126 Videoway ............................................ 07, 23, 50, 129 Vid Tech ................................................................ 64 Vidtek .................................................................... 64 Viewstar ..................... 13, 22, 58, 62, 20, 40, 26, 107 Zenith ................................................. 07, 23, 50, 129
CABLE BOX IN OUT
VIDEO
IN OUT R AUDIO L
VIDEO VHF/UHF
Do normal Timer Record if... � PlusCode number is not listed for program. � program (e.g. sports event) may run over set stop time. See page 6 of �Basic Operations� book to: � cancel a timer recording in progress. � review, replace, or clear program contents.
OUT TO TV
IN 1 OUT
When STOP is pressed during normal recording, press : a) 1 key (NOW) � to mark now. �NOW MARKING COMMERCIALS� appears. b) 2 key (LATER) � to mark after power is turned off. (If tape is rewound and another recording is started before power is turned off, correct marking may not occur. c) ACTION (CANCEL) � marking is canceled. OFF : The VCR will not mark commercials. Select when editing or dubbing a tape, or when opting not to use this feature.
Index Search
Program End Search
Press SEARCH/ M/A SKIP to display SEARCH in Stop or Play mode, and then press NUMBER keys to select recording number. � To calculate number, see below. Press FF or REW on the remote to start search. Play begins at search end. To search forward or back 1 index, press FF or REW on the remote or VCR while screen left is displayed (10 sec.). � To cancel, press STOP or PLAY. Locates end point of recording for continuity.
1
INDEX
SEARCH PROG. END
MOVIE
ENTER INDEX NUMBER :1 USING 1- 9 KEYS FORWARD SEARCH :FF REVERSE SEARCH :REW NEXT :SEARCH M/A SK I P EXIT :STOP
1 Press SEARCH/ M/A SKIP twice to
display SEARCH in Stop or Play mode.
2
INDEX
SEARCH PROG. END
Press FF on the
MOVIE
VCR
Audio Mode for Recording
(Display disappears after 5 seconds.)
Audio Mode for Playback
See p. 5 of �Basic Operations� Instruction book.
1 Press SAP/ Hi-Fi to display audio mode. 1 Start playback.
You Cannot
Important for DSS/Cable Box Users � When recording via DSS, the receiver must be left on. When recording via cable or antenna, DSS receiver must be off. � When recording via a cable box, leave box on and tuned to channel to be recorded.
4 Press ACTION again to return to normal screen.
The most commonly asked questions about
SEARCH START :FF NEXT EXIT :SEARCH M/A SK I P :STOP
remote to start PROGRAM END SEARCH. � To cancel, press STOP or PLAY.
Question
How fast does the VCR advance through commercials?
Answer
The VCR advances through a 3-minute commercial block in about 8 to 12 seconds if the tape speed is SLP. In SP, it takes about 25 to 35 seconds.
2
INDEX SEARCH
Examples of Program End Search. Fig. 1
the current tape position Press SEARCH button
I Connect With Two Cable Boxes
VCR CABLE BOX IN OUT
VIDEO AUDIO
You Can
2
STEREO SAP MONO
R
IN FROM ANT.
L VHF/UHF
OUT TO TV
IN 1 OUT
ANT or
A/B Switch
2-Way Splitter CABLE BOX
OUT 1 OUT 2
CATV
IN OUT
IN 1 IN 2
� record and view � view channel other than both scrambled and the one unscrambled selected for channels if any type of additional recording. TV equipment is � do a Timer added. IN OUT This connection recording of R AUDIO requires: two a channel L converter unless you VIDEO boxes, an A/B select it at VHF/UHF the cable switch, and a 2box. way splitter.
Press SAP/ Hi-Fi repeatedly to select desired mode.
� Refer to �Receivable Broadcast Types� above.
2 Press SAP/ Hi-Fi to display audio mode.
(Display disappears after 5 seconds.)
Tape Operation
Repeat Play
Set to playback a recording over and over.
Are commercials advanced through only when I Yes. The commercials are not marked until after the recording is finished. playback a recording? Are commercials still recorded on the tape in Yes. By setting the C/A PLAYBACK to MANUAL, see top of this case I choose to view them sometime? page, you can view or advance through commercials as desired.
Program 1
Program 2 or BLANK
INDEX
FORWARD SEARCH :FF REVERSE SEARCH :REW
Zero Search
To quickly return to a specified tape location.
Does speeds? work in all recording Yes. works in SP, LP, and SLP.
FF
End Point
Program 2
Fig. 2
Program 1
3
H I F I : L/R HIFI : L HIFI : R NORMAL
Press SAP/ Hi-Fi repeatedly to select desired mode.
� Select �HIFI(L/R)� or �HIFI(L)� or �HIFI(R)� to listen to stereo recordings in stereo sound. Select �NORMAL� for monaural sound.
BLANK
BLANK
INDEX
INDEX
1 Press ACTION to display menu. 2
REPEAT PLAY REMOTE WARNING AUTO SHUT- OFF
1 Press DISPLAY during play to display
Counter.
� Arrow indicates selection.
Does the VCR advance through commercials each time I playback tapes which were recorded using ?
Yes. As long as C/A PLAYBACK is set to AUTO, see top of this page, the VCR should advance through commercials each time the tape is played back.
To Calculate Index Number Example 1:
To go to rec. 2 from rec. 4, enter 3 and press REW. Fig. 3
INDEX
the current tape position Press SEARCH button
FF
the current tape position Press SEARCH button
End Point
Program 2
VCR
C/A
CLOCK
3 Do a recording.
See p. 5 of �Basic Operations� Instruction book.
Notes � Arrow indicates selection.
:OFF :ON :OFF
CH
Press to select REPEAT PLAY and press OFF. to set ON or
2
PLAY
1 2 : 0 0AM
0 : 00 : 00 SP
IDIOMA/LANGUE : ENGLISH VCR� S OUTPUT CH :3 SELECT : ACT I ONSET : : EXIT
Press RESET COUNTER at desired position to reset to �0:00:00�.
After marking commercials, does the VCR stop at The tape stops at the end of the recording so that any additional the end of the tape, or rewind to the beginning? timer recordings can be performed. Can I play my nonrecordings in VCRs? Yes. marked recordings will play in nonVCRs, but commercials will not be advanced through.
Program 1
BLANK
ON : Play repeats at tape end or if unrecorded portion over 30 sec. is detected.
1
2
3
4
5
6
7
Does the marking process interfere with other
DSS Brand Code Numbers
Toshiba ................................................................. Hitachi/ Hughes .................................................... Magnavox/ Uniden 1 ............................................. Magnavox/ Uniden 2 ............................................. 92 93 94 95 Panasonic ............................................................ 96 RCA ..................................................................... 97 Sony ............................................................. 98, 105
� Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard stereo tapes will playback in monaural sound. � To listen to Hi-Fi stereo playback, the VCR AUDIO (L/R) jacks must be connected to a stereo TV or an external stereo amp and speakers. (See top of this page.) � If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio. � Hi-Fi and normal audio playback volume level may differ.
3 Press ACTION to return to normal screen.
3 Continue to record, playback, etc. 4 Press STOP. 5 Press CA/ZERO in
REW 1 2 : 3 0AM CH 02 0 : 30 : 30 SP
STOP 1 2 : 3 1AM CH 02 0 : 00 : 00 SP
programmed recordings? What happens if I cancel the marking in progress so I can use the VCR?
No. If the interval between 2 or more timer programs is not sufficient to mark the recording, marking will be done after all recordings are complete and the power goes off. Marking will be resumed when the VCR's power is turned off as long as the tape has not been ejected.
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
1
End Point
FF
2
3
4
5
6
7
Upon locating end point,
If search exceeds a few seconds in BLANK area.
What if part of my program is advanced through Please see the 3rd note on top of this page. along with the commercials? Additional Notes: � Because of the various ways in which commercials are broadcast, the VCR may not be able to recognize all commercials. � If a timer recording is scheduled for the middle of the night, please be aware that the VCR will make some noise as it rewinds and fast forwards the tape while marking commercials. and are registered trademarks of SRT, Inc. A Jerry lggulden invention licensed in association with Arthur D. Little Enterprises, Inc. U.S.Pat. No. 5,333,091; 5,692,093; 5,696,866 other patents pending
NOTE: Note
indicates start points of each recording.
Important Notes
� Due to changes in infra-red commands used by manufacturers, some brands have several codes. If your unit does not respond to the first code, please try the next one. � Some TV, Cable Box and DSS Box brands require you to turn on the power manually.
*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. -3-4-5-
Stop mode to start ZERO SEARCH. � Unit will go into FF or REW mode and stop at the last point the Counter was set to 0:00:00.
� search continues 7 sec. past end point, � tape rewinds to 10 sec. before end point, � tape plays to end point and stops.
Notes � If Program End Search is started very close to an index mark, that mark may be skipped over. � To cancel, press PLAY or STOP.
� Advanced Connections � Multi-Brand Control Feature
� If Index Search is started very close to an index mark, that index mark may not be counted in the search. *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.
-2-
-6-
-7-
