CASIO PRG70-1B
Manual de Usuario

MO0405-EA

Operation Guide 2872
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to read this manual carefully and keep it on hand for later reference when necessary.

�

Expose the watch to bright light to charge its battery before using it.
You can use this watch even as its battery is being charged by exposure to bright light. � Be sure to read �Power Supply� of this manual for important information you need to know when exposing the watch to bright light.

Applications
The built-in sensors of this watch measure direction, barometric pressure, temperature and altitude. Measured values are then shown on the display. Such features make this watch useful when hiking, mountain climbing, or when engaging in other such outdoor activities.

�

If the digital display of the watch is blank...
If the PS indicator is on the display (either flashing or steady), it means that the watch�s Power Saving function has turned it off to conserve power. Power Saving automatically

�

� The initial factory default setting is Power Saving on. � The watch will recover from the sleep state if you move it to a well-lit area, if you press any button, or if you angle the watch towards your face for reading. It can take up to two seconds for the display to turn on. � See �Power Saving� for more information.

�

Warning! � The measurement functions built into this watch are not intended for taking measurements that require professional or industrial precision. Values produced by this watch should be considered as reasonable representations only. � When engaging in mountain climbing or other activities in which losing your way can create a dangerous or life-threatening situation, always be sure to use a second compass to confirm direction readings. � CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any claims by third parties that may arise through the use of this watch.

About This Manual
Sensor

� Button operations are indicated using the letters shown in the illustration. � Each section of this manual provides you with the information you need to perform operations in each mode. Further details and technical information can be found in the �Reference� section.

(Light)

turns off the display and enters a sleep state whenever the watch is left for a certain period where it is dark.

*

*

General Guide
� The illustration below shows which buttons you need to press to navigate between modes. � In any mode, press L to illuminate the display.
Countdown Timer Mode Stopwatch Mode
Press C.

� You can use buttons B, D, and E to directly enter a sensor mode from the Timekeeping Mode or from another sensor mode. To enter a sensor mode from the Stopwatch, Countdown Timer, Data Recall, or Alarm Mode, first enter the Timekeeping Mode and then press the applicable button.
Sensor Modes
Press B. Press D. Press E.

Digital Compass Mode

Altimeter Mode

Barometer/ Thermometer Mode

Data Recall Mode

Alarm Mode

�
Press C.

Timekeeping
Month � Day
Press A.

Day

Use the Timekeeping Mode to view the current time and date. You also need to enter the Timekeeping Mode to configure timekeeping settings, as well as the display illumination duration and Power Saving setting. � In the Timekeeping Mode, press A to toggle between the month�day and the day of the week�day at the top of the display.

3. When the timekeeping setting you want to change is flashing, use D and/ or B to change it as described below. � The following steps explain how to configure timekeeping settings only. Screen To do this: Do this: Reset the seconds to 00 Change the hour or minutes Toggle between 12-hour (12H) and 24-hour (24H) timekeeping Press D. Use D (+) and B (�). Press D. Press D (+) and B (�).

PM indicator Seconds Hour : Minutes Day of week

Change the year, month, or day

4. After the settings are the way you want, press A to exit the setting screen. Note � For information about specifying how long the display remains illuminated, see �To specify the illumination duration�. � For details about configuring settings for the Power Saving feature, see �Power Saving�. � Resetting the seconds to 00 while the current count is in the range of 30 to 59 causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are reset to 00 without changing the minutes. � With the 12-hour format, the P (PM) indicator appears on the display for times in the range of noon to 11:59 p.m. and no indicator appears for times in the range of midnight to 11:59 a.m. � With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without any indicator.

To set the time and date

1. In the Timekeeping Mode, hold down A until the seconds start to flash, which indicates the setting screen. 2. Press C to move the flashing in the sequence shown below to select other settings.
Seconds Power Saving Hour Minutes 12/24-Hour Format

Day

Month

Year

�

�

�

Timekeeping Mode

�

1