HITACHI PJ-TX100
Manual de Servicio

PJ-TX100(C11H)

6-10 Related Messages
When the unit�s power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.
Message CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. Description The time the lamp timer has counted is approaching 2000 hours. Preparation of a new lamp, and an early lamp change is recommended. After you have change the lamp, please be sure to reset the lamp timer.

The time the lamp timer has counted is approaching 2000 hours, so a lamp change within ** hours is recommended. When lamp usage reaches referring to the section �Lamp�. After you have changed Please change the lamp by 2000 hours, the power will automatically be turned off. THE POWER WILL TURN OFF the lamp, please be sure to reset the lamp timer. AFTER ** hr. CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIMER. THE POWER WILL TURN OFF AFTER 0 hr. NO INPUT IS DETECTED ON *** SYNC IS OUT OF RANGE ON *** fH *****kHz fV *****Hz There is no input signal. Please con�rm the signal input connection, and the status of the signal source. The horizontal or vertical wavelength of the inputted signal is outside of the response parameters of this unit. Please con�rm the specs for this unit or the signal source specs. The internal portion temperature is rising. Please turn the power OFF, and allow the unit to cool down at least 20 minutes. After having con� rmed the the air passage aperture? the power ON again. � Is there blockage of following items, please turn � Is the air �lter dirty? � Does the peripheral temperature exceed 35°C? A note of precaution when cleaning the air �lter. Please immediately turn the power OFF, and clean or change the air �lter by referring to the �Air Filter� section of this manual. After you have cleaned or changed the air �lter, please be sure to reset the �lter timer. If the same message is displayed after the treatment, please clean the transparent area of �lter cover and the dust-detecting window, according to the following. As the time the lamp timer has counted has reached 2000 hours, the power will soon be automatically turned off. Please immediately turn the power off, and change the lamp by referring to the section �Lamp�. After changing the lamp, please be sure to reset the lamp timer.

CHECK THE AIR FLOW

CLEAN THE AIR FILTER POWER OFF FIRST, THEN CLEAN THE AIR FILTER. AFTER CLEANING THE AIR FILTER, RESET THE FILTER TIMER.

NOTE � A lamp has a �nite product life. Lamps are characterized by the fact that, after long hours of usage, a lamp will no longer light up, or the lamp will break or burst, etc. This projector is equipped with an automatic shut-down function, such that the power will automatically be turned off when lamp usage time has reached 2000 hours. Please be aware, however, that among lamp types, there are major differences in product lifetimes; a lamp may thus fail to light even prior to the functioning of the automatic shut-down function of this projector.

CAUTION
� The transparent area of �lter cover and the dust-detecting window should be cleaned for normal operation of the optical dust detecting system. Please pay attention not to remain �ber or fragment of cloth inside the duct. 1. Turn off the projector, and unplug the power cord. 2. After making sure that the projector has cooled adequately, remove the filter cover. Hold the release buttons of the filter cover, while pulling up it. 3. Wipe the transparent area of the filter cover by using a swab or a soft cloth. 4. Remove the air filter.

Air filter Release buttons Filter cover Release buttons Dust detecting window (Rear side) (Bottom side)

Hold the release buttons of the air filter, while pulling up it. 5. Wipe the dust-detecting window by using a soft cloth. Transparent area 6. Replace the air filter and filter cover.

26