SHURE PG4
Manual de Usuario

english

System Components

Startup
Follow these simple steps to check for interference and to set your receiver and transmitter to the same channel.
PS20 Power Supply

5 If you haven�t installed the
cover off.

battery, do it now and leave the

Features
Busy Indicator
When selecting channels, a flashing dash indicates interference from television broadcasts, electronic devices or other wireless systems.

Locking and Unlocking Transmitter Controls
Lock system controls to prevent accidental muting. To lock controls: Turn transmitter off. Remove Battery Cover. Press and hold Channel Button. Press and release Power/Mute button. Power/Mute LED will flash red and green. To unlock controls: Press and hold Power/Mute button down until Power/Mute LED flashes red and green.

1 Turn OFF the microphone
or bodypack.

6 Turn ON the handheld or

bodypack transmitter by pressing the power button.

If this occurs, change the channel.

audio

ready

channel

audio

ready

channel

PG88 Dual Wireless Receiver

If left on, it will create a false busy indicator.

m

ute

mu

t

e

mute

Changing Channels
Press and hold the channel button until the display starts flashing.
Internal Anten

Multiple gain settings are available on the PG1 and PG2 transmitters. To change gain settings, see below.

Accessing Gain Switch

2 Plug in the power supply.
Diversity Antenna System PG4

The channel display should illuminate.
c ha nne l

cha

n

nel

rea While the display is audio flashing, dy press the channel button.

mute

channel

audio

ready

channel

The channel display should PG4 Wireless Receiver illuminate. There is no power switch. PG1 Bodypack Transmitter PG2 Handheld Transmitter

It turns off after ten seconds to conserve battery.

nel an ch

The channel is active once the display stops flashing.
annel

0dB For instrument or quiet to normal vocal performance (default).
ch

�10dB Use if audio is distorted due to high vocal or instrument levels. mic Use for headworn or lavalier microphones (PG1 only).

3 Press and hold down the
channel button until the display begins flashing.
Internal Anten

7 Check to see that the

transmitter and the receiver display the same channel.
audio ready channel

Internal Antenna Diversity

Receiver and transmitter channels should match.
audio ready channel

Wearing the Bodypack Transmitter
Internal Antenna Diversity

Clip the transmitter to belt or guitar strap as shown. Make sure the antenna is unobstructed.

audio

ready

channel

mt ue

PG185 Lavalier Mic

If you see the Busy Indicator (a flashing dash) change the channel.

mt ue

c h ann e l

c h an

C

ongratulations on purchasing your Shure

Performance Gear Wireless system. Shure professional audio products deliver legendary sound quality, stage-proven durability and
©2006, Shure Incorporated 27EN8865 (Rev. 2)

hassle-free setup for worry-free performance. Performance Gear Wireless systems are available in a variety of configurations for handheld, guitar, headset, and presentation applications.
Printed in U.S.A.

4 Wait for the channel display to stop flashing.
PG30 Headworn Mic
audio

Internal Diver

The ready LED on the receiver should be illuminated.
audio ready

ne l

Testing Audio
Internal Diversity Antenna Syste

channel

read

y

channel

8 Replace battery cover.

Talk or sing into the microphone or play instrument. The audio LED on the receiver should flicker green or amber, if red, adjust the Gain Switch.
mt ue

Changing Battery Internal Diver Expected life for a 9 volt alkaline battery is approximately 8 hours.When the
Power/Mute LED glows red, the battery should be replaced immediately.

audio

ready

channel

c h ann el

pgw_en.indd 1

5/31/2006 9:05:51 AM