Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5894 visitantes online.
Productos
Información
Destacado
Inicio >> SAMSON >> MPL1204 Manual del propietario
 
 0 artículo(s) en Su carrito 

SAMSON MPL1204
Manual del propietario


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del SAMSON MPL1204 Manual del propietario

Es una guía completa (también conocida como Manual de Operación o Manual del Propietario), y está disponible en formato PDF. Después de colocar su orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
Guided Tour - Main Section
certain that one or more connected mics require 48 volts phantom power, leave this switch off (its out position). 10: Meter switch - When out, the ten-segment MPL 1204 meter (see #6 on the previous page) shows the continuous output level of Bus 1-2; when pressed in, the meter shows the continuous output level of Bus 3-4. 11: Tape switch - Press this in to route signal connected to the rear panel RCA jack tape inputs to channels 11 and 12 (the left side is routed to channel 11 and the right side is routed to channel 12). When this switch is pressed in, any mic or line input signal connected to channels 11 and 12 is automatically muted. 12: Main Level - This knob determines the final signal level of the rear panel Main output�you can think of it as being the �master fader.� The 2 o�clock �0� position of the knob indicates unity gain (no level attenuation or boost). Moving the knob counterclockwise from the �0� position (towards ���) causes the signal to be attenuated (at the very bottom, it is attenuated infinitely�in other words, there is no sound). Moving it clockwise from the �0� position (towards �+10�) causes the signal to be boosted by up to 10 dB. For more information, see the �Setting The Correct Gain Structure� section on page 14 in this manual. 13: Control Room Level - This knob determines the signal level of the rear panel Control Room output, allowing independent monitoring of the Main output signal. The 2 o�clock �0� position of the knob indicates unity gain (no level attenuation or boost). Moving the knob counterclockwise from the �0� position (towards ���) causes the signal to be attenuated (at the very bottom, it is attenuated infinitely�in other words, there is no sound). Moving it clockwise from the �0� position (towards �+10�) causes the signal to be boosted by up to 10 dB. 14: Bus L/R switches - These switches allow you to route the output from the four buses to the Main left/right output jacks and Control Room left/right output jacks on the rear panel (see #10 and #11 on page 10). When this switch is up, the signal from that bus is not routed to the main outputs and instead terminates at its Bus out jack (see #12 on page 10). When pressed in, the signal from that bus is routed to the Main and Control Room outputs (buses 1 and 3 are routed to the left Main and Control Room output jacks and buses 2 and 4 are routed to the right Main and Control Room output jacks) as well as to its Bus out jack. For more information, see the �Busing, Submixing and Channel Muting� section on page 17 in this manual. 15: Bus Faders (white with blue line) - These linear sliders determine the relative level of the four bus outputs. The �0� position of each fader indicates unity gain (no level boost or attenuation). Moving the fader below this position (towards the ��� position) causes the signal to be attenuated (at the very bottom, it is attenuated infinitely�in other words, there is no sound). Moving it above this position (towards the �+10 dB� position) causes the signal to be boosted by up to 10 dB. For best signal-to-noise ratio, all Bus faders should generally be kept at or near the 0 level. For more information, see the �Setting The Correct Gain Structure� and the �Busing, Submixing and Channel Muting� sections on pages 14 and 17 in this manual.

10

Quizás también quiera comprar

$4.99

SX-K700 TECHNICS
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

CJ-V51 PIONEER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

GRAND PRIX ELECTRONIC 754 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

SX-PR602 TECHNICS
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

EV-S1000E SONY
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …

$4.99

GRAND PRIX ELECTRONIC 780 BECKER
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

AG7330 PANASONIC
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…

$4.99

MECABLITZ 60 CT4 METZ
Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo genera…
>
Parse Time: 0.174 - Number of Queries: 127 - Query Time: 0.044