INFINITY KAPPA1.1CS
Manual de Usuario

IMPORTANT: Installation of automotive stereo components can require extensive experience with a variety of mechanical and electrical procedures. Although these instructions explain how to install a Kappa Series 3-Way Component System in a general sense, they do not show the exact installation methods for your particular vehicle. If you do not feel you have the experience, do not attempt the installation yourself, but instead ask your Authorized Infinity Car Audio Dealer about professional installation options. WARNING: Playing loud music in an automotive environment can permanently damage your hearing, as well as hinder your ability to hear traffic. The maximum volume levels achievable with Infinity speakers, combined with high power amplification, may exceed safe levels for extended listening. We recommend using low volume levels when driving. Infinity accepts no liability for hearing loss, bodily injury or property damage as a result of use or misuse of this product.

INSTALLATION WARNINGS AND TIPS
� Always wear protective eyewear when using any tools. � Turn off all audio systems and other electrical devices before you start. Disconnect the (�) negative lead from your vehicle�s battery. � Keep components in their package until final installation. When moving a speaker, always rest it with the cone or dome facing up. Never use force to install any speaker. � Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws. Remember that the screws can extend behind the surface. � At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. CAUTION: In some cars, fuel tanks may be located directly beneath the rear deck. Check for adequate speaker basket clearance before considering this location! � Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl, to keep material from snagging in a drill bit or saw. � For door installations, check the clearance with the windows throughout the range of the window�s travel, and verify that a mounted speaker will not interfere with the window crank or power window mechanism. � If mounting components elsewhere, check for clearance around rear deck torsion bars, glove box or other structural elements. � Do not mount components where they will get wet.

WIRE CODES
Single Stereo Amplifier

Amplifier

RIGHT + � � + LEFT
GRN RED + GRN/BLK GRN/WHT BLK � GRN

� BLK
+ � � + � + � +

+ RED
+ �

Connect Pigtail Jumpers As Shown
WOOFER

SPEAKER PLACEMENT
Kappa speakers are designed to be easily installed in stock speaker locations. While mounting your speakers in the original factory locations will, in most cases, provide excellent sonic results, the best sounding installations are a result of adherence to a few basic rules: � For the most spacious stereo image, place the left and right speakers as far apart as possible. � For enhanced center image, place the left and right speakers so they are equidistant from the listening position. If possible, try to place them as far forward as possible. � For best treble response aim the tweeters toward the listening position, and be sure there are no obstructions between the tweeters and the listener.

BLU/BLK To LEFT Woofer

�

+ HI

REFERENCESystem Crossover Network Component STANDARD AUTOMOTIVE
� TO LEFT MIDRANGE +
LO HI

TO RIGHT WOOFER + � HI LO

BLU

�

LO

TO LEFT TWEETER +
MID

HI

HI

TO RIGHT TWEETER +
MID

GRY/ RED/ BLK BLK GRY RED
Figure 1. This application shows connections for a Kappa1cs system and one stereo amplifier.

RED/ GRY/ WHT WHT RED GRY

� + HI
To LEFT 4" Midrange

� + MID
To LEFT Tweeter

+ MID �
To RIGHT Tweeter

-2-

FROM RIGHT AMPLIFIERS

MIDRANGE EMIT TWEETER LO

�

+

�

EMIT TWEETER MIDRANGE

FROM LEFT AMPLIFIERS � LO HI TO LEFT WOOFER +

WOOFER

�
HI +

BLU/WHT To RIGHT Woofer BLU

TO RIGHT MIDRANGE +
HI LO

�

+ HI �
To RIGHT 4" Midrange