JVC GY-DV5100U
Manual de Usuario

7. SHOOTING OPERATION

7. SHOOTING OPERATION

7-2 Searching for Recorded Scenes (Edit Search)
8. To stop recording:
Press the VTR trigger button on the unit or on the lens section again. The TALLY lamp and REC indicator lamp go out and the unit enters the record-standby mode. When the VTR trigger button is pressed, the unit enters the record-standby mode after rewinding the tape for about 2 seconds (back-spacing).
OPEN

In the record-standby mode, it is possible to search for a scene when you want to check the recorded scene or continue recording from the scene.

EDIT SEARCH

REC BATT ALARM

7.8

9. To restart recording:
Press the VTR trigger button on the GY-DV5100 or lens.

1 3200K 2 5600K 1/8 ND .3 5600K

EDITSEARCH MONITOR

EDIT SEARCH + button

FILTER

.4 5600K 1/64 ND

SHUTTER

STATUS
LCD BRIGHT DISPLAY

MENU

AUDIO LEVEL

PULL OPEN
CH-1 AUDIO IN AUDIO SELECT CH-1 CH-2 AUTO MANUAL FRONT REAR CH-2

10.Ending recording:

AUTO IRIS

BACK L NORMAL SPOT L

FULL AUTO

BLACK

STRETCH NORMAL COMPRESS

LOLUX

CH-1

CH-2

ATUS

EDIT SEARCH � button

MODE
VTR CAM

8. TALLY lamp
7. 8. 9. VTR trigger button

Press the VTR trigger button to enter the record-standby mode and perform the following operations as required. � When it is required to unload the videocassette: 1 Slide the OPEN knob to open the cassette cover. 2 Press the EJECT button to take out the videocassette. � When the power should be turned off Set the POWER switch to OFF. When the camera is not going to be used for a long period, detach the battery pack. About the QUICK REC START Mode If the VTR trigger button is pressed immediately after the videocassette is inserted, the mode becomes the QUICK REC START mode that enables quick start of recording. However, when shooting starts in the middle of the tape, a blank space appears as the new scene will not be linked smoothly with the previous image. Also, the time code does not continue. (Some overlap may also occur.)

POWER
ON OFF

VTR

Screen indications during Edit Search During Edit Search, the VTR mode is indicated as ED.FWD or ED.REV on the LCD monitor or in the viewfinder. (When Status 1 screen is displayed.)

Engage the record-standby mode. � Searching the tape in forward direction 1. Press the EDIT SEARCH + button. While the + button is pressed, playback takes place at the normal speed.

00:00:00:00 20min FAS �3dB FAW I SD FIL1 B F5.6 48k 12.2V ED.FWD 01/02/03 AM01:23:45

2. When the EDIT SEARCH + button is released, the standby
mode is reengaged. � Searching the tape in reverse direction 1. Press the EDIT SEARCH � button. While the � button is pressed, playback takes place at -1times the normal speed.

2. When the EDIT SEARCH � button is released, the standby
mode is reengaged.

MEMO:
� Block noise may appear and the image may freeze during search.

7.8. TALLY lamp
OFF ZEBRA ON SKIN AREA AUTO WHITE ACCU FOCUS VTR

ED.FWD: Forward search ED.REV: Reverse search

AUDIO LEVELE CH-1
5

7. 8. 9. VTR trigger button

CAUTION:
� The unit enters the STOP mode automatically at TAPE END. If this mode continues for 3 minutes, the mode switches to the tape protect mode. � See �LONG PAUSE TIME item on the OTHERS (1/2) menu screen� on page 86. � If the VTR trigger button is pressed very quickly and repeatedly, or the POWER switch is moved immediately after the trigger button is pressed, the viewfinder REC indicator lamp may blink and the GY-DV5100 may not enter the record mode. To remedy this condition set the POWER switch to OFF and wait for 5 seconds or more before turning the power on again. � A neat transition to the next recorded scene cannot be guaranteed if a recording is ended by turning the POWER switch or DC power supply OFF, or by removing the battery pack. � Trial-shooting is always recommended before recording important events to confirm the recording is satisfactory. � The microphone may pick up the sound of the lens� iris if the iris is changed abruptly or the iris is manually moved abruptly during recording. If the sound is found annoying, please purchase an optional microphone in order to move the microphone away from the lens or ensure that the iris is not changed abruptly during shooting.

55

56