ROLAND FR-3S
Manual de Usuario

V-Accordion r Treble Octave Tx

Treble Octave Tx
(�3~0~3, Default setting: 0) This parameter allows you to transpose the Noteon messages transmitted by the Treble

Orchestra TX/RX Channel

trO

(Off, 1~16, Default setting: 3) This parameter allows you to define the MIDI channel for the Treble Orchestra part.

OrC

section up to three octaves up or down. This can be used for songs where an accordion register of the Treble section (for example) should be doubled by a piccolo flute played by an external module whose notes would be far too low if they were used as is. As stated above, each MIDI note has a unique number. This parameter allows you to add (or subtract) 12 (�1� octave), 24 (�2� octaves) or 36 (�3� octaves) to (from) the note numbers generated by your playing.
Note: �TX� means that this parameter only applies to the note messages transmitted to external devices. Messages the FR-3 receives from another device are not affected by it.

The assignment set here applies both to the transmission (�TX�) and reception (�RX�) of MIDI data. Obviously, �TX� is only used when �MId� (see above) is set to �Out�, while the �RX� part is only used when �MId� is set to �In�.

Orchestra Octave TX
(�3~0~3, Default setting: 0) This parameter allows you to transpose the Noteon messages transmitted by the Orchestra section.
Note: �TX� means that this parameter only applies to the note messages transmitted to external devices. Messages the FR-3 receives from another device are not affected by it.

OrO

Bass/Free Bass TX/RX Channel
(Off, 1~16, Default setting: 2) This parameter allows you to define the MIDI channel for the bass buttons or Free Bass (accordion) section, depending on which mode is

bFr

Orchestra Bass TX/RX Channel

currently active. The assignment set here applies both to the transmission (�TX�) and reception (�RX�) of MIDI data. Obviously, �TX� is only used when �MId� (see above) is set to �Out�, while the �RX� part is only used when �MId� is set to �In�. Select �Off� if the Bass or Free Bass section should neither receive nor transmit MIDI data.
Note: Though it is perfectly possible to assign the same MIDI channel to several sections, the result is usually disappointing and may lead to a lot of confusion.

(Off, 1~16, Default setting: 5) This parameter allows you to define the MIDI channel for the ORCH BASS part. The

Obs

assignment set here applies both to the transmission (�TX�) and reception (�RX�) of MIDI data. Obviously, �TX� is only used when �MId� (see above) is set to �Out�, while the �RX� part is only used when �MId� is set to �In�.

Orchestra Bass Octave TX
(�3~0~3, Default setting: 0) This parameter allows you to transpose the Noteon messages transmitted by the ORCH BASS part.

ObO

Bass/Free Bass Octave TX
(�3~0~3, Default setting: 0) This parameter allows you to transpose the Noteon messages transmitted by the bass

bfO

Orchestra Chord TX/RX Channel

buttons or Free Bass section up to three octaves up or down.

(Off, 1~16, Default setting: 6) This parameter allows you to define the MIDI channel for the ORCH CHORD part. The

OCH

Chord TX/RX Channel
(Off, 1~16, Default setting: 3) This parameter allows you to define the MIDI channel for the chord buttons when

CHd

assignment set here applies both to the transmission (�TX�) and reception (�RX�) of MIDI data. Obviously, �TX� is only used when �MId� (see above) is set to �Out�, while the �RX� part is only used when �MId� is set to �In�.

they are used to play the selected accordion register. The assignment set here applies both to the transmission (�TX�) and reception (�RX�) of MIDI data. Obviously, �TX� is only used when �MId� (see above) is set to �Out�, while the �RX� part is only used when �MId� is set to �In�.
Note: Though it is perfectly possible to assign the same MIDI channel to several sections, the result is usually disappointing and may lead to a lot of confusion.

Orchestra Chord Octave TX
(�3~0~3, Default setting: 0) This parameter allows you to transpose the Noteon messages transmitted by the ORCH CHORD part.

OCO

Orchestra Free Bass TX/RX Channel
(Off, 1~16, Default setting: 7) This parameter allows you to define the MIDI channel for the ORCH FREE BS part. The

Ofb

Chord Octave TX
(�3~0~3, Default setting: 0) This parameter allows you to transpose the Noteon messages transmitted by the chord buttons up to three octaves up or down.

CHO

assignment set here applies both to the transmission (�TX�) and reception (�RX�) of MIDI data. Obviously, �TX� is only used when �MId� (see above) is set to �Out�, while the �RX� part is only used when �MId� is set to �In�.

49