Su carrito de compras está vacío
 
English Polski Spanish 
Buscar un manual
 

(p.Ej. AA-V20EG JVC, ZX-7 Sony)
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Usuarios conectados
Actualmente hay 5923 visitantes online.
Productos
Información
Destacado
Inicio >> SHARP >> FO-4400 Manual de Servicio
 
 0 artículo(s) en Su carrito 

SHARP FO-4400
Manual de Servicio


¡Twitee acerca de este producto y obtenga $1.00 de crédito en la tienda para uso!
  • Contiene diagramas del circuito
  • Descargable
  • Formato PDF
  • Manual completo
  • Idiomas: English
Precio: $4.99

Descripción del SHARP FO-4400 Manual de Servicio

Manual de servicio completo en formato digital (archivo PDF). Los manuales de servicio por lo general contienen diagramas de circuitos, tarjetas de circuitos impresos, consejos para reparación, diagramas de cableado, diagramas de bloque y lista de refacciones. El Manual de Servicio (a veces llamado Manual de Reparación) es usado principalmente por los técnicos.

Si tan solo quiere saber cómo utilizar su televisión, reproductor de vídeo, reproductor de mp3, etc. Quizá lo que necesita es el Manual del Propietario. Después de colocar la orden le enviaremos las instrucciones de descarga a su dirección de e-mail.

The manual is available in languages: English

Not yet ready
You must purchase it first

Opiniones de los clientes
No hay comentarios de productos.

TEXT_PDF_SNIPPET
[5] Installation
1. Site selection
Take the following points into consideration when selecting a site for this model.

2Connecting the telephone line cord

FO-4400U FO-CS1

Insert one end of the line cord into the jack on the back of the machine marked TEL. LINE. Insert the other end into a standard (RJ11C) single-line wall telephone jack. Note: The fax machine is set for touch-tone dialing. If you are on a pulse dial (rotary) line, you must set the fax machine for pulse dialing by changing Option Setting 22.

ENVIRONMENT

� � �

The machine must be installed on a level surface. Keep the machine away from air conditioners, heaters, direct sunlight, and dust. Provide easy access to the front, back, and sides of the machine. In particular, keep the area in front of the machine clear, or the original document may jam as it comes out after scanning. The temperature should be between 50° and 86°F (10° and 30°C). The humidity should be between 30% and 85% (without condensation).

� �

ELECTRICITY
AC 120 V, 60 Hz, grounded (3-prong) AC outlet is required.

3 Attaching the ADF exit tray
Insert the protrusion on the right side of the machine into the hole in the right side of the ADF exit tray 1 , then bend the tray slightly and insert so that the protrusion on the left side of the machine goes into the hole on the left side of the ADF exit tray 2 . Pull out the tray extension 3 .

Caution!

� �

Connection to a power source other than that specified will cause damage to the equipment and is not covered under the warranty. If your area experiences a high incidence of lightning or power surges, we recommend that you install a surge protector for the power and telephone lines. Surge protectors can be purchased at most telephone specialty stores.

1

TELEPHONE JACK
A standard RC11C telephone jack must be located near the machine. This is the telephone jack commonly used in most homes and offices. � Plugging the fax machine into a jack which is not an RC11C jack may result in damage to the machine or your telephone system. If you do not know what kind of jack you have, or need to have one installed, contact the telephone company.

2

3

If the machine is moved from a cold to a warm place...
If the machine is moved from a cold to a warm place, it is possible that the reading glass may fog up, preventing proper scanning of documents for transmission. To remove the fog, turn on the power and wait approximately 2 hours before using the machine.

4 Attaching the received document tray
Slide the received document tray into the machine as shown. When Important!: The received document tray must be attached for the fax machine to operate properly. it stops, lift the end slightly and push in so that the tray locks into place.

2. Assembly and connections

1Connecting the power cord

Connect the female end of the power cord to the fax machine as shown. Insert the male end into a 120 V, 60 Hz, grounded (3-prong) AC outlet.

Important!: The fax machine requires its own dedicated power outlet. The power outlet must not be shared with any other devices. In particular, do not use an extension cord to connect multiple devices to the outlet. Note: If your area experiences a high incidence of lightning or power surges, we recommend that you install surge protectors for the power and telephone lines. Surge protectors can be purchased at most telephone specialty stores.

5 Verification Stamp option (FO-45VS)
Note: This feature is available as an option. Consult your dealer if you wish to use this feature. When transmitting a document, you can have the fax machine stamp each document page as it is scanned. After scanning, you can check to see if all document have been stamped to verify that no double feeds occurred. (A double feed occurs when two pages are fed through the scanner at once, which means that one of the pages is not scanned.) To use this function, have your dealer install the Verification Stamp option, and then set Option Setting 29 to ON.

Press the power switch to turn on the power.

1�4

Quizás también quiera comprar

$4.99

FO4400 SHARP
Manual de Usuario

Manual del propietario completo en formato digital. El manual estará disponible para descarga como …
>
Parse Time: 0.357 - Number of Queries: 101 - Query Time: 0.098