SONY DXC-D30WSP
Manual de Servicio

(ABC

MARK/CUE:MARK mFREEZE:OFF CHG REEL NO: (YESm4)

3

Press the MENU/STATUS switch to move the text entry arrow. Press the MENU/STATUS switch upward to move the cursor to the right or downward to move it to the left.

Item

Settings

MARK/CUE MARK (normal value), CUE Selects MARK See �Using the ClipLink Function� mode or CUE mode (page 41). FREEZE See �Using the Freeze Mix Function� Sets the freeze mix (page 44). function. CHG REEL NO Sets the cassette name/number
Chapter 4 Viewfinder Screen Indications and Menus

4

Press the UP/ON button or DOWN/OFF button to enter the desired characters. The displayed character changes each time the UP/ ON button is pressed. It changes in reverse order each time the DOWN/OFF button is pressed.

See �To set the cassette name/ number� below.

To set the cassette name/number (when using DSR-1/1P)

5 6

Return to step 2 and repeat the text entry procedure. After completing text entry, move the text entry cursor to the parenthesis position. The display changes as follows.

1 2

Connect the DSR-1/1P and load a cassette. Press the MENU/STATUS switch to move the cursor to CHG REEL NO, then press the UP/ON button.

MARK/CUE:MARK FREEZE:OFF mC H G R E E L N O : ( Y E S m4)

7
The cursor (�) changes to the text entry arrow (�) and the current cassette name/number is displayed. (�NO TAPE� is displayed if you neglected to load a cassette.)

Check your cassette name/number setting, and press the UP/ON button if no more changes are required. (To make changes or to abort the procedure for this setting, return to step 2.) This writes the new cassette name/number to the cassette memory, after which the display changes as follows.

54

Chapter 4

Viewfinder Screen Indications and Menus

�

1-34 DXC-D30WS/P(E)/V1
Viewfinder Basic Menu
Basic menu page 7
The following display is shown when the DSR-1/1P is connected.
MARK/CUE:MARK FREEZE:OFF CHG REEL NO: )

Basic menu pages 8 and 9
You can create a title of up to four lines, each of twelve alphanumeric or punctuation characters, and
Current cassette name/number

4

Press the UP/ON button to select the required character. Each time you press the UP/ON button, the character cycles through the following sequence.
ABCDEFGHIJKLMNOPQRSTUVWXYZ?;x/0123456789: -., (Space)

then save it. It is then possible to record the title over the picture while shooting. Entering the title (page 8)

1

Press the MENU/STATUS switch as necessary to display basic menu page 8 (title setting display) in the viewfinder.

To reverse the character sequence With the UP/ON button held down, press the DOWN/OFF button.

5

Press the DOWN/OFF button to confirm the character selection. The cursor advances to the next character position. To change a character after confirming it Return to step 3, and input the character again.

mTITLE SET?

6
If a title is already present, it appears on this screen. To delete the displayed title, press the UP/ ON and DOWN/OFF buttons simultaneously.

Repeat steps 4 and 5 until the title is complete.

DXC-D30

Chapter 4 Viewfinder Screen Indications and Menus

2

Press the UP/ON button. This brings up the cursor on the screen (flashing), and switches to title editing mode.
Initial cursor position

7

When the title is complete, press the MENU/ STATUS switch as necessary to return to the normal viewfinder indications. The title created is retained, even when you power the camera off.

MARK/CUE:MARK FREEZE:OFF CHG REEL NO: mW R I T E ? ( Y E S m4) (DEF )

To record a title (page 9)

1

Press the MENU/STATUS switch as necessary to access basic menu page 9 (title display).

3

Press the DOWN/OFF button to move the cursor to the position where you wish to insert a character. To move the cursor back With the DOWN/OFF button held down, press the UP/ON button.

mTITLE IND?

(continued)

Chapter 4

Viewfinder Screen Indications and Menus

55