PIONEER DV-490V-S/RLFXZT
Manual de Servicio

5

6

7

8

No.
4

Symptoms
A tray cannot be opened. (An opening screen is displayed on the monitor)

Diagnosis Contents
Does the voltage of CP2302-pin 3 and pin 1 on the DVD MT Assy change normally ? Pin 5 (SW2(TRIN)): Tray is fully closed: "L" Pin 3 (SW1(TROUT)): Tray is fully opened: "L" Is a LOAD-DRV signal reaching ?

Possible Defective Points
Tray SW
A

DVD MT PCB Assy DVD IC (IC4001)

Are the signals output from IC2301-pin 5 and pin 6 (CP2302-pin 4 and pin 5) on the DVD MT Assy ? DVD MT PCB Assy Pin 5: Approx. 4.5 V during opening tray approx. 0V during closing tray. FTS Driver IC (IC2301) Pin 4: Approx. 0V during opening tray approx. 4.5 V during closing tray. Are wires of CP2302 and CP2303 on the DVD MT Assy disconnected or damaged ? Does the voltage of CP2303-pin 5 change by pressing the Inside switch. 5 Playback impossible (no focusing) Are the signals output from IC2301-pin 9 (F+) and pin 8 (F�) on the DVD MT Assy ? Does 650-nm LD emit light ? Does a pickup lens move up / down ? Does an actuator spring bend ? Are plastic parts damaged ? Or is a shaft detached ? Is the turntable detached or tilted ? Is flexible cable of CP2301 on the DVD MT Assy disconnected or damaged ? Is signal output from IC4001-pin 42 (FOSO) on the DVDMT Assy ? (Device control of about 1.4 V is output usually. It is fluctuated by about ± 250 mV with focus up / down.) 6 Playback impossible (Spindle does not turn) Are the signals output from IC2301-pin 13 (MOT SPDL�), and pin 14 (MOT SPDL+) on the DVD MT Assy ? Is pin 41, 42 (STBY) fixed LOW? Is there any part detached from the spindle motor ? Or Is there any foreign object lodged in it ? Are wires of CP2303 on the DVD MT Assy disconnected or damaged ? Is signal output from IC4002-pin 37 (DMSO) on the DVD MT Assy ? 7 Playback impossible (Playback stops) Does 650-nm LD deteriorate ? If the voltage at each both ends of R2321 and R2323 on the DVD MT Assy is 0.4 V or more, the 650-nm LD is definitely deteriorated. Does 780-nm LD deteriorate ? If the voltage at each both ends of R2320 and R2322 on the DVD MT Assy is 0.4 V or more, the 780-nm LD is definitely deteriorated. Are there scratches or dirt on the disc ? 8 Picture disturbance during playback (block noise, freeze, other) No sound (Picture is normal) Are there scratches or dirt on the disc ? Is there a problem with the format of the disc ? Connector / cable Inside switch DVD MT PCB Assy FTS Driver IC (IC2301) Pickup Mechanism section (motor) Flexible cable / connector DVD MT PCB Assy DVD IC (IC4001) DVD MT PCB Assy FTS Driver IC (IC2301) Mechanism section (Spindle motor) Flexible cable / connector DVD MT PCB Assy DVD IC (IC4001) 650-nm LD deteriorated. (When playback of a DVD is impossible) 780-nm LD deteriorated. (When playback of a CD is impossible) Disc Disc
C B

D

9

Is signal output from IC4001-pin184 and pin 186 on the DVD MT Assy DVD MT PCB Assy ? DVD IC (IC4001)

E

F

DV-490V-S
5 6 7 8

63