|
Usuarios conectados
Actualmente hay 5560 visitantes y 41 usuarios online.
|
Productos
|
Información
|
Destacado
|
|
|
|
|
No hay comentarios de productos.
Loading the print cartridge (continued) To replace the print cartridge
If the ribbon indicator flashes and the inserted paper emerges after you insert the paper and the paper is automatically loaded, remove the print paper and replace the print cartridge. Open the cartridge compartment lid and push up the eject lever. Remove the used print cartridge and replace it with a new one.
Eject lever
Inserting the print paper
Inserting the print paper using the supplied automatic feeder
By using the supplied automatic feeder, you can supply the print paper automatically.
1
Notes on using automatic feeder � If trouble occurs in feeding the print paper, the lamp on the printer flashes. Remove the feeder from the printer and check that there is no paper jammed in the printer. When you reinstall the feeder and press the print button, the printer prints the set number of copies again. � The feeder can hold up to 25 sheets of paper. When you add paper to a partially full feeder, make sure that the total number of sheets does not exceed this limit. If you do, the paper may jam. � Do not place different types of paper in the feeder. If you do, the paper may jam. � To insert paper after the feeder is attached to the printer, first remove the feeder from the printer and then insert the paper into the feeder. � While printing, do not open the feeder lid. If you do, the paper may jam.
Open the lid of the paper tray by sliding the switch on front to the right.
Paper supply indicator Ribbon error indicator
Push up the eject lever, then remove the used print cartridge.
Setting Up Setting Up
To load the half-used ink ribbon cartridge
While pressing the center of the reel, wind the ink ribbon in the direction of the arrow. Wind the ribbon until the black line comes to the left edge.
2
Make sure that the spacer is raised.
Spacer
3
Notes on storing the print cartridge � Avoid placing the cartridge in a location subject to: � high temperatures � high humidity � excessive dust � direct sunlight � When you are going to store a partially-used cartridge for an extended period of time, store it in its original bag.
If ink ribbon should tear Repair the ribbon with transparent tape. There should be no problem with using the remaining portion of the ribbon. Before loading the ink ribbon cartridge into the printer, turn the reel until the transparent tape can no longer be seen.
Riffle the print paper to avoid jamming the print paper.
Repair with transparent tape.
Make sure not to touch the printing surface (the glossy side where nothing is printed).
14GB
Setting Up
Setting Up
15GB
Inserting the print paper (continued)
4
Insert print paper with its printing surface (the side where nothing is printed) facing up. Make sure not to touch the printing surface and not to bend the corners of the paper. You can load up to 25 sheets of print paper or the print paper designed for the printer into the feeder. Make sure that the metal tabs on both sides fir over the print paper.
Printing surface
7
Press �Push� on the cover of the automatic feeder, then insert the feeder until it clicks.
8
Press the print button of the printer. The print paper is automatically loaded into the printer and printing starts.
Front
Inserting the print paper manually
Paper Metal tab To stop continuous printing Set the dial to 1. Printing stops after the current printing finishes. If print paper runs out during continuous printing
Insert the print paper sheet by sheet. This section explains how to insert the standard type print paper. Use the print paper designated for this printer only.
5
Turn on the printer and press MEMORY or CAPTURE to store an image for printing. For the details, refer to �Printing� in the operating instructions of the printer.
1 2 3
Turn on the power of the printer. The POWER indicator lights up. Follow printing procedures. For details, see pages 20 to 39. Insert the print paper straight with its blank printing surface facing up, along the guide to the left of the paper port. Insert the paper until less than 2 cm (approx. 0.8 inches) remains. The paper is automatically loaded when printing starts.
6
Turn the dial to set the number of copies to be printed continuously. You can set 1, 2, 3, 4, 5,10 or 25 copies. Turn the dial until the desired number appears in the window. Make sure it clicks at that time. Otherwise, you may get the wrong number of copies.
2
Remove the feeder from the printer. Then, insert more print paper into the feeder and reinstall the feeder to the printer. The printing resumes automatically. Notes on inserting the print paper manually � Insert the print paper straight along the guide to the left of the paper port. If the paper is positioned to the right or slanted, the printing area may get out of position. � The paper may not be loaded automatically if you do not insert the paper firmly.
To print a number of copies not specified on the dial Insert the desired number of sheets and set the dial to 25.
Guide
Less than 2 cm
16GB
Setting Up
Setting Up
17GB
Confidential 1-3
DMP-1000P (AEP)
|
|
|
> |
|