PIONEER CP-EU8
Manual de Usuario

INSTALLATION
In order to minimize the transmission of vibrations from the speaker to the floor, PIONEER offers two possibilities : 4 metal decoupling spikes to be screwed under the base. If desired (especially with polished wood floors), you can also employ the 4 provided metal bases between the 4 decoupling spikes and the floor. 4 foam cushions to be stuck on the underside of the base.

CAUTION : Make sure you assemble the stand on a flat surface that is relatively soft (such as a carpet). Note that these spikes are sharp metal and can cause damage to flooring. Make sure to lay down a cloth or suitable base before setting up. The spike bases should be placed as shown below (with the depression on the top side).

There are two alternative methods for mounting the S-EU8BS-LR loudspeaker on the matching CP-EU8 speaker stand. (see images A and B on first page). Solution A : Use the foam cushions provided with the S-EU8BS-LR loudspeaker, positionned between the underside of the speaker cabinet and the top plate of the stand. Solution B : Use the decoupling spikes (also provided with the SEU8BS-LR loudspeaker) between the underside of the speaker cabinet and the top plate of the stand.
Remark : The specifications and design of this product are subject to change without notice, in the interests of improvements.

Make sure to use the spike bases provided to avoid damaging the surface where you place the stand.

CABINET AND STAND MAINTENANCE
Use a polishing cloth or dry cloth to wipe off dust and dirt. If the cabinet or stand is very dirty, use a soft cloth dipped in some neutral cleanser diluted 5 or 6 times with water. Finally, wipe again using a dry cloth. Do not use furniture wax or cleaners. Never use thinners, benzine, insecticide sprays and other chemicals on or near the cabinet or stand, since these will corrode the surfaces.

SPECIFICATIONS
External dimensions ........ 367 (W) mm x 720 (H) mm x 405 (D) mm Weight ..................................................................................... 9.7 kg
SUPPLIED ACCESSORIES Base plate ....................................................................................... 2 Pole ................................................................................................. 2 Top plate ......................................................................................... 2 Screw (M5 x L50 mm) [SBA6010] ................................................ 16 Decoupling Spike [SBA6008] .......................................................... 8 Base for decoupling Spike [SBA6001] ............................................ 8 Screw (M4 x L40 mm) ..................................................................... 4 Screw (M4 x L50 mm) ..................................................................... 4 Washer [SBE1036] ......................................................................... 4 Spring Washer [SBE1035] .............................................................. 4 Foam cushion [FREC-067] ............................ 2 sheets (4 pcs/sheet) Instruction manual [SRD6061] REPLACEMENT PART NUMBERS Part name Part no.

Top spacer Top protector Bottom protector Spacer for Top plate Spacer for Base plate Packing case

[SHA6056] [SHA6057] [SHA6058] [SHA6059] [SHA6060] [SHG6226]

Published by Pioneer Corporation. 2006 Pioneer Corporation. All reproduction and translation rights reserved.

PIONEER CORPORATION

4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153, Japan PIONEER ELECTRONICS (USA) INC. P.O. BOX 1540, Long Beach, California 90801-1540 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada PIONEER EUROPE N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium Tel : +32-3-570.05.11 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia, Tel : (03) 580-9911 PIONEER ELECTRONICS DE MEXICO S.A. DE C.V. San Lorenzo Num 1009 3er piso Desp. 302 Col. Del Valle, Mexico D.F.; C.P. 03100 Tel : 5-688-52-90

Printed in China <SRD6061-A>