GEMINI CDJ-10
Manual de Usuario

INTRODUCTION
Congratulations on purchasing a Gemini CDJ-10 CD Player. This state of the art professional CD player is backed by a three year warranty, excluding lasers. One year warranty on CD lasers. Prior to use, we suggest that you carefully read all the instructions.

PLAY/PAUSE : Each press of the PLAY/PAUSE BUTTON (9) causes the operation to change from play to pause or from pause back to play. See the CUE INSTRUCTIONS section for more information. TRACK SKIP : The TRACK SKIP BUTTONS (6) let you select
the track to play.

CAUTIONS
Do not use this CD Player at temperatures below 41°F/5°C or higher than 95°F/35°C. Place the unit in a clean and dry location. Do not place the unit in an unstable location. When disconnecting the power cord from an AC outlet, always grasp it by the plug. Never pull the power cord. To prevent electric shock, do not remove the cover or the bottom screws. There are no user serviceable parts inside. Please refer servicing to a qualified technician. Do not use chemical solvents to clean the unit. Keep the laser pickup clean by keeping the tray closed. Keep this manual in a safe place for future reference.

SEARCH BUTTONS : The SEARCH BUTTONS (7) are used to move foward or reverse while in play mode. The SEARCH BUTTONS (7) are also used to accurately position the disc at the point where you wish the track to start playing. This position on the track is memorized as the cue point. See the CUE INSTRUCTIONS section for more information. STOP
: The STOP BUTTON (11) will end the playing of the CD.

TIME: The TIME BUTTON (12) switches the time display between the three available choices listed under DISPLAY. CUE: With the unit in the play mode, and after memorizing the cue point, pressing the CUE BUTTON (8) will cause the CD player to enter the pause mode at the memorized cue point. Holding down the cue button changes the cue function to preview (allowing you to hear the
music play from the cue point) and releasing the cue button returns you to the preset cue point. If a cue point is not memorized, pressing the CUE BUTTON (8) will cause the unit to return to the beginning of that track.

SAFETY CERTIFICATIONS
Laser Diode Properties Material: Ga - Al - As Wavelength: 755 - 815 nm (25° C) Laser Output: Continuous Wave, max. 0.5mW

PITCH: Pushing the PITCH BUTTON (14) activates the pitch section of the unit. The pitch of the CD will change according to the position of
the PITCH CONTROL (15). CONTINUOUS: The CONTINUOUS (13) function will cause the unit to play continuously (after the last track, the unit will return to the first track of the disc and continue to play).

LINE VOLTAGE SELECTION
Model CDJ-10 is a dual voltage unit. It will operate at 115 or 230 volts. To set the proper voltage follow these steps: 1. Place the head of a screw driver in the center of the VOLTAGE SELECTOR SLIDE SWITCH (3) found on the rear panel. 2. Slide the switch left for 115 volts or push the switch right for 230 volts. 3. Do not force or twist the switch. Excessive force may cause damage. If the switch does not move smoothly, contact a qualified technician.

OPERATING INSTRUCTIONS
1. Make sure that the VOLTAGE SELECTOR SLIDE SWITCH (3), found on the rear panel, is set for the proper voltage. Plug the unit in and press the POWER SWITCH (2). 2. Press the OPEN BUTTON (16), place a CD in the DISC TRAY (10) and close the tray door. The display will initially show the number of tracks and the total time of the CD. 3. Push the TRACK SKIP BUTTONS (6) to select the track you want to play. 4. Press the PLAY/PAUSE BUTTON (9) and the unit will instantly play.

CONNECTIONS
1. Plug one end of a set of RCA connectors into each of the LINE OUTPUT JACKS (1). 2. Plug the other end of the RCA connectors into any available line level input jacks on your mixer. If you are playing the CDJ-10 through a receiver, you can plug the RCA connectors into the CD or AUX input jacks on your receiver. If there are no CD or AUX inputs, use any line level (not phono) inputs.

CUE INSTRUCTIONS
1. To start the play at a point other than the beginning of a track, follow these instructions: First choose the track you wish to play, and then press the PLAY/ PAUSE BUTTON (9) so the unit goes into the play mode. Press the PLAY/PAUSE BUTTON (9) to pause play at the spot where you want the play to start -- the CUE POINT. Press the PLAY/PAUSE BUTTON (9) again to save the cue point. Press the CUE BUTTON (8) to pause play at the cue point (the unit will go into the pause mode and the location indicated on the display will be the memorized cue point). You can preview the cue point by pressing and holding down the CUE BUTTON (8). Press the PLAY/PAUSE BUTTON (9) to begin play from the cue point. Note: After a cue point is set, pressing the TRACK SKIP BUTTONS (6) clears the cue point. When you press the CUE BUTTON (8) in the new track, the beginning of that track will be the new cue point. 2. Once you have saved a cue point you can fine tune or change the memorized cue point: To change a cue point, push the PLAY/PAUSE BUTTON (9) so the unit plays from the cue point, then press the PLAY/PAUSE BUTTON (9) at the spot you wish your new cue point to be. Press the PLAY/ PAUSE BUTTON (9) again to save the cue point. The unit will go into the pause mode and the location indicated on the display will be the new memorized cue point. Page 2

FUNCTION DESCRIPTIONS
POWER SWITCH: After making sure that the VOLTAGE SELECTOR SLIDE SWITCH (3), found on the rear panel, is properly set, plug the unit in and press the POWER SWITCH (2). The unit will turn on. Pushing the POWER SWITCH (2) a second time will turn the unit off. DISC TRAY: The DISC TRAY (10) is where the CD is held. Pressing the disc tray OPEN BUTTON (16) will open the tray. OPEN BUTTON: Press the OPEN BUTTON (16) to open the DISC TRAY (3). DISPLAY: The DISPLAY (4) shows the track numbers, play mode, pause mode, and 3 different time displays. These time displays are time elapsed on the track, time remaining on the disc and time remaining on the track. PLAYBACK DISPLAY: The PLAYBACK DISPLAY (5) displays the time remaining to play and flashes slowly when the track has 30 seconds left. The PLAYBACK DISPLAY (5) flashes quickly when the track has 15 seconds left.