PHILIPS AZ1018
Manual de Servicio

Power Supply Radio
Radio reception Programming radio stations
CD

You can store up indicator to eventually a goes total out of if 30 the radio
AZ1 01 TTE 8RDE RECOR CASSE CD RADIO
L I F T

TO

OPE N

PAU I SE F LT

STO � P OPE
OFF

TO

to protect your set during heavy
REC TTE RECO
CD RADIO CASSE

OPE N

INSTRUCTIONS FOR USE

L I F T

TO

OPE N

PAU STO P

PLAY SE

T BAT LOW

change. station.
CD MO M DE GRA PRO

Using AC Powerthisto301fromnumberaallocatestartsdisplaytheinfrequencywhen
FM
H

3-2

�M W
S E AR C

4 Press CD MODE/ PROGRAM again to con�rm the setting. � To tune to a weak station, press SEARCH number and frequency of the preset have found optimal reception. To improve reception stations. POWER slider to CD, RADIO or presetthedisappears,PROGRAMDisplay:�localyourtocorrespondsset,theoftuning.automaticduringSrchshows

onshownasvoltage,mainstheifCheck1radioatotunesautomaticallyThe�

PR ES ET

Displayreception.suf�cientofstationbottomtheonlocatedplatetype

mains supply. If it does not, consult your dealer or service centre.

General operation � or § brie�y and repeatedly until you station are shown.
1 To select your sound source adjust 5 Repeat the above four steps to store other TAPE/OFF. � For FM, pull out the telescopic aerial. Incline 2 Adjust sound with the VOLUME and another frequency in its place. DBB (Dynamic Bass Boost) controls. preset station is shown. the cassette keys are released. slider to TAPE/OFF position and check built-in so the telescopic aerial is not � For MW (AM) the set is provided with a To switch off set, adjust POWER Press PRESET 3 or 4 until the desired and turn aerial. Reduce its length if the signal is too strong (very close to a transmitter). Tuning to preset stations

�

PCS 107 139
TAP OFF

� If BATT LOW lights up, battery power 4 To switch off completely, unplug the mains

is running low.The BATT LOW lead from the wall socket. memory.theinstationssocketwallthefromleadmainsUnplug�
POW ER

MWFM

ORD RDE R

01 8 AZ1
PLAY
SEA RCH CD

batteries are too weak.
UME N VOL TAP
MWFM

POW ER

Batteries contain chemical substances, thunderstorms.
REC ORD

BAT T LOW
PLAY
RCH SEA
SE

PLAY PAU SE VOL P �UME OPEN
STO

PAU

so they should be disposed of properly.
P STO

theonlocatedisplatetypeThe
T CD MO M DE LOW BAT GRA PRO

FM
AR C H
PR ESET

PLAY SE PAU �M W

set.theofbottomcausecanbatteriesuseIncorrect
S E STO P
MO DE CD PRO GRA

M

electrolyte leakage and will corrode the
FM �M W
S H

E A R C

compartment or cause the batteries to burst.Therefore: Save energy 1 Adjust the POWER slider to RADIO.
A S T E M IT
EA K
SY

Switching power on/off:

ES ET PR

N

SS RE FL

IG
SP EX
ER

� R Do not mix types: e.g. alkaline with Whether you � are U Display: using shows mains tu or brie�y.The battery L T radio E D Reception).

BA

type for set. consumption always adjust the POWER slider TAPE/OFF and check if 2 Press FM�MW once or more to select the cassette keys are released. desired waveband. 2 Press CD MODE/ PROGRAM to
CD RADIO
CD MWFM TAP OFF

carbon frequencyzinc. isOnly thenuse shown.batteries 1of Tunethe tosame yoursupply, desiredto stationavoid (seeunnecessary Radioenergy

� When inserting new batteries, do not try to
AZ1 01 TTE CASSE 8RDE RECOR

mix old batteries with the new ones. �ashes.Display:�PROGRAM � Remove batteries if the set is not to be
ER POW

� Display: shows your waveband activate programming. §or�SEARCHdownholdandPress3 �

REC ORD

PLAY

SE PAU

STO � P OPE

VOL

N UME

SEA RCH

brie�y tune a radio station. Release Press PRESET 3 4 once or more to

used for a long time.

� You can erase a preset station by storing

2 Connect mains lead to AC MAINS needed. Direct aerial by turning the whole

inlet and wall socket.The power supply Note:When set is switched off the tuner set. is now connected and ready for use. presets will be retained in the set�s memory.

4 To switch off radio, adjust the POWER

selector, adjust selector to match the cassette keys are released. local mains. Disconnect the mains lead if this reset.betohasselector

slider to TAPE/OFF position and check 3 If your set is equipped with a voltage