PHILIPS 6000SX/00
Manual de Usuario

ENGLISH

7

Preparing for use � � � � � � HB604/6000SX only:The tanning appliance should be placed on a smooth, level floor. This appliance may only be installed by an authorised electrician. It requires two people to assemble and move the tanning appliance. During assembly the appliance becomes heavier and more difficult to move.We therefore advise you to assemble the appliance at the place where it will be used. Make sure there is enough free space beside (at least 50 cm), behind (at least 30 cm) and in front (at least 1 metre) of the appliance. HB604/6000SX only: Leave approx. 50 cm free space behind the tanning appliance to allow assembly of the exhaust unit. If the couch and/or canopy have to be placed on the floor, put them on the floor with the tube lamps facing downwards to avoid internal damage. Make sure you place them on a soft surface (e.g. a carpet or rug) to prevent damage to the housing (fig. 1).

1 Assemble the legs of the frame by fastening the angle sections with the bolts supplied (fig. 2). 2 Place the couch on the legs carefully. Make sure the legs slide steadily into the appropriate openings in the couch (fig. 3). � � � � NB: the openings for assembling the canopy must be located at the back of the couch. If necessary, you can move the couch slightly by sliding its legs across the floor or by carefully lifting it slightly off the floor together with another person. Make sure there is enough free space beside (at least 50 cm), behind (at least 30 cm) and in front (at least 1 metre) of the appliance. HB604/6000SX only: Leave approx. 50 cm free space behind the tanning appliance to allow assembly of the exhaust unit. Never try to move the appliance in the manner shown in the picture.This could cause the frame to become detached from the couch (fig. 4).

3 Lift the canopy together with another person and position its connecting tubes over the connecting holes. Slide the tubes steadily into the connecting holes of the couch (fig. 5). B Be careful not to get your fingers stuck between the couch and the canopy. B Make sure the cords do not get stuck between the couch and the canopy. 4 Fasten the side panel brackets to the legs by means of the bolts supplied for this purpose (fig. 6).
B

5 Fasten the side panels to the side panel brackets with the bolts supplied (fig. 7). NB: the Velcro strips should be pointing forwards. 6 Open the cover of the power supply unit. 7 To connect the cords of the couch to the connectors inside the power supply unit, loosen the nut of the cord relief bushing (fig. 8). 8 Place the cord relief bushing in the appropriate recess of the power supply unit and tighten the nut (fig. 9).

�

The 3 cord relief bushings of the cords connected to the canopy should be placed in the recesses on the right-hand side.The 2 cord relief bushings of the cords connected to the couch should be placed in the recesses on the left-hand side (fig. 10).

9 Connect the cord connectors to the appropriate connectors in the power supply unit. The connectors have been colour marked. B Insert the cord connectors in the connectors of the power supply unit that are marked with the same colour. B HB604/6000SX only: Connect the power supply cable of the exhaust unit. 10 Close the cover of the power supply unit (HB600/3200SX and HB601/4000SX only). 11 Put the mains cord behind the power supply unit and push the power supply unit slowly and carefully under the couch from the front (fig. 11).
B

12 Press the front panel against the side panels, exerting exert some pressure to ensure that the Velcro strips engage properly (fig. 12). The purpose of the panel is to hide the power supply unit and the legs from view and to enhance the appearance of the appliance. 13 HB604/6000SX only: Place the exhaust unit behind the tanning appliance (fig. 13). 14 HB604/6000SX only: Press the back panel against the rear side of the appliance (fig. 14). 15 HB604/6000SX only: Fasten the encasing of the exhaust unit to the panels of the tanning appliance. 16 HB604/6000SX only: Fit the hose supplied with the appliance between the exhaust opening of the tanning appliance and the exhaust unit and fasten it with the hose clamp supplied (fig. 15). 17 HB604/6000SX only: Fit a discharge hose with a 25cm diameter and a length of max. 3m to the top cover of the exhaust unit.

Avoid acute bends in the hose! The counterpressure at the fan outlet may not exceed 150 Pa. 18 HB604/6000SX only: Fasten the hose by means of a hose clamp (fig. 16). 19 Close the canopy. 20 Put the mains plug in the wall socket. Using the appliance User's instructions for using the appliance �
B

As owner of this tanning appliance, you should give your customers the following instructions. For your convenience we have also included these instructions in a separate section that can be cut out of this manual and can be made available to customers. The control panel shows all the functions that have to be adjusted (fig. 17). Symbol � blinks on the display.

� �