HITACHI 50EX39B
Manual de Usuario

Table 2-17-l. r

lynamic convergence
stment Item

adjustment
Adj. VR

of the horizontal

line (RED/BLUE).
Adjustment Details

RED 1 BLUE

H
2

1

Horizontal center line

Vertical Veritcal

skew V-SKEW bow V-BOW

1 RU25

1 RU53

1

Remove Correct straight

the inclination the bow distortion line. the bow distortion line. the inclination the bow distortion line. the inclination

of the horizontal of the horizontal

center

line. line and make it a

I

center

I-

Upper/lower pincushion distortion V-PIN Upper/lower keystone distortion V-KEY Upper pincushion distortion V-U-PIN

RU05

RU33

Correct straight Remove Correct straight Remove

of the lower horizontal of the lower horizontal

line and make it a line. line and make it a line.

RU13 RUOI

RU4�l RU29

of the upper horizontal of the upper horizontal

7 H
8

Upper keystone distortion V-U-KEY Vertical

Upper/lower horizontal line

size V-SIZE linearity V-LIN

RU09

RU37

Match upperflower the vertical size. Match upper/lower the linearity.

horizontal horizontal

line with the green line by changing line with the green line by changing

Vertical

Note:

1. Adjustment procedure of the horizontal lines (I) Center, (2) Lower, (3) Upper and then (4) Upper/Lower. 2. Accurately match the horizontal center lines (red/blue) with the green line using the centering magnets (item 2.7). 3. The adjustment VRs shown in items 7 and 8 of above table (RU19, RU47, RU17, RU45) as well as BVCenter (RUP4), BH-Center (RUP8), RV-Center (RUQS), and RH-Center (RUQ7), should have been set to their mechanical centers previously.
Dynamic
Adjustment

Table 2-l 7-2.

convergence
Item

adjustment

of the vertical

line (RED/BLUE).
Adjustment Details

II
1 2 Vertical center line

NO.

T
skew H-SKEW bow H-BOW RU82 RU80 RU61

Horizontal Horizontal Left/right distortion Left/right distortion

II
1 RUE1 RU90 1 RU98 RUA6 RUA3 RUK2 RU86

RUE3

Remove Correct straight Correct straight Remove Extend side.

the inclination

of the vertical

center

line. line and make it a line and make it a

the bow distortion line. the bow distortion line. the inclination 2nd vertical

of the vertical

center

pincushion H-PIN keystone H-KEY size H-SIZE linearity H-LIN

of the right side vertical of the right side vertical

RU69 RU76 RU73 RUJ3 RU57

line. +

5 6

Right side vertical line

Horizontal Horizontal ;igRhE;d --

line from the left/right

Match 2nd vertical line from the right end with green line. Match right end line with the green line. line and make

1) �

line linearity

8 9 -10 11 Left side vertical line

Left pincushion distortion H-L-PIN Left keystone distortion H-L-KEY Left horizontal size H-L-SIZE FF_ _;;,� line linearity

Correct the bow distortion it a straight line. Remove Match line. the inclination left side vertical

of the left side vertical

RU65 RULl RUJ7

I

RU94 RULS RUK6

I

of the vertical

line on the left side. rv I

line with the green line with the green

h$a$h lefl end vertical

+

Note:

1. 2. 3. 4.

Adjustment procedure of the vertical lines (1) Center, (2) Right, and then (3) Left line. Accurately match the vertical center lines (red/blue) with the green line using the centering magnets (item 2.7). The adjustment VRs shown in items 5, 6, 7, 10 and 11 (RU76, RUAG, RU73, RUA3, RUJ3, RUK2, RULI, RULS, RUJ7 and RUKG) as well as RH-Center (RUQ7), BH-Center (RUP8), should have been set to their mechanical centers previously. Including centering magnets, adjust repeatedly as required.

27